True Wireless Earbud Reset
If sound is only coming out of one earbud, these instructions are for you.
True Wireless Earbuds can sometimes un-sync from one another requiring a manual reset to enable them to auto sync to one another. This “un-syncing” can happen when only one earbud is being used (single earbud mode) or when a Bluetooth device connects to one of the earbuds prior to the two earbuds syncing to each other when they are removed from the charging case powered on.
Sync earbuds together by following steps below:
- From your devices Bluetooth menu, delete “Wicked Mojo 700” pairing name.
- Place earbuds in charging case.
- Turn on earbuds by removing them from the charging case.
- With both earbuds out of the case and turned on, tap either the left OR right earbud 5 times. After tapping 5 times, you will hear the earbuds beep 5 times and both earbuds will automatically turn off.
- Return both earbuds to charging case.
- Remove earbuds from charging case. Earbuds will automatically sync to each other. When successfully synced, only 1 earbud will show a flashing white LED.
- Once synced together you can locate “Wicked Mojo 700” in your device’s Bluetooth settings.
Turning Earbuds On/Off
Power On
Removing the earbuds from the charging case automatically turns them on and starts the syncing process to one another.
Power On (outside of case)
When outside the charging case and powered off, long press both earbuds for 2-3 seconds (White LEDs) to turn them on.
Power Off
Placing the earbuds back into the charging case will automatically power them down
Power Off (outside of case)
Long press left or right earbud for 5 seconds to turn off earbuds without putting them in the case.
Charging
Charging the Charging Case
Using a USB-C charging cable, plug into a power source. While charging the charging case LED will flash WHITE. Once fully charged, 4 LEDs will be solid WHITE.
Charging the Earbuds
Place earbuds in charging case to charge earbuds. They will turn off and automatically begin charging. While charging the earbuds, the charging case LED will be solid WHITE. When the earbuds are full charged, the charging case LEDs will shut off.
Tip: Earbuds will announce “low charge” when they are at 10% battery life.
Charging the Earbuds
Place earbuds in charging case to charge earbuds. They will turn off and automatically begin charging. While charging the earbuds, the charging case LED will be solid WHITE. When the earbuds are full charged, the charging case LEDs will shut off.
Tip: Earbuds will announce “low charge” when they are at 10% battery life.
LEDs
Charging Case
LEDs when charging Case:
Flashing WHITE LEDs
Charging Case
4 solid WHITE LED’s
Full Charge Reached
Charging Case
LEDs when charging Earbuds:
Solid WHITE
Charging Earbuds
OFF
Earbuds fully charged
Functions
| Pause / Play |
Double Tap |
(Left or Right Earbud) |
|
Next Track |
Long Hold (2 seconds) |
(Right Earbud) |
|
Previous Track |
Long Hold (2 second) |
(Left Earbud) |
|
Enter / Exit Voice Assistant |
Triple Tap |
(Left Earbud) |
|
Answer Call / Hang Up Call |
Single Tap |
(Left or Right Earbud) |
|
Reject Incoming Call |
Long Hold 2 Seconds |
(Left or Right Earbud) |
|
Change between Gaming and Music Mode |
Triple Tap |
(Right Earbud) |
|
Transparency Mode On/Off |
Quadruple Tap |
(Left or Right Earbud) |
|
Volume Up |
Single Tap |
(Right Earbud) |
|
Volume Down |
Single Tap |
(Left Earbud) |
Connecting to the App
The Mojo 700 can connect to the Wicked Audio App. To learn more, go to go.wickedaudio.com/app
Troubleshooting
Reset
Only one earbud connecting to device at a time?
- From your devices Bluetooth menu, delete “Wicked Mojo 700” pairing name.
- Place earbuds in charging case.
- Turn on earbuds by removing them from the charging case.
- With both earbuds out of the case and turned on, tap either the left OR right earbud 5 times. After tapping 5 times, you will hear the earbuds beep 5 times and both earbuds will automatically turn off.
- Return both earbuds to charging case.
- Remove earbuds from charging case. Earbuds will automatically sync to each other. When successfully synced, only 1 earbud will show a flashing white LED.
- Once synced together you can locate “Wicked Mojo 700” in your device’s Bluetooth settings.
Trouble connecting to the app
- Confirm Wicked Audio product is fully charged.
- Remove Wicked Audio pairing name from Bluetooth setting on your device.
- Turn off Bluetooth on your device.
- Make sure the Wicked Audio app is not running in the background on your device.
- Remove earbuds from charging case and allow them sync together.
- Turn on Bluetooth setting on your device.
- Pair earbuds to your device.
- Open the Wicked Audio app.
- Click on “Add Device.”
 |
WARNING INGESTION HAZARD THIS PRODUCT CONTAINS A BUTTON CELL OR COIN BATTERY. DEATH or serious injury can occur if ingested. A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours. KEEP new and used batteries OUT OF REACH OF CHILDREN. Seek immediate medical attention if battery is suspected to be swallowed or inserted inside any part of the body. |
PRECAUTIONS
LISTENING TO AUDIO AT EXCESSIVE VOLUMES CAN CAUSE PERMANENT HEARING DAMAGE. USE AS LOW A
VOLUME AS POSSIBLE.
Over exposure to excessive sound levels can damage your ears resulting in permanent
noise-induced hearing loss (NIHL). Please use the following guidelines established by the Occupational Safety Health
Administration (OSHA) on maximum time exposure to sound pressure levels before hearing damage occurs.
SAFE USE
& HAZARD WARNINGS
90 dB SPL at 8 hours
95 dB SPL at 4 hours
100 dB SPL at 2 hours
105 dB SPL at 1
hours
110 dB SPL at 30 min.
115 dB SPL at 15 min.
120 dB SPL Avoid as damage may occur
IMPORTANT SAFETY INSTRUCTION
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings
4 Follow all instructions.
Attention should be drawn to the environmental aspects of battery disposal; The use of apparatus in moderate climates.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
LIMITATION OF LIABILITY Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment. The device has been evaluated to meet general
RF exposure requirement. The device can be used in portable exposure condition without restriction. In no event,
under any cause of action of theory of liability, shall Premier Accessory Group, LLC, its distributors or suppliers
be liable to you or any third party for indirect, incidental, consequential, special, exemplary or punitive damages,
of any and all nature whatsoever, arising out of use of or inability to use a product.
This includes without
limitation, property damage, loss of value of the product or any third party products that are used in or with the
Premier Accessory Group, LLC products, even if the Premier Accessory Group, LLC product has been advised of the
possibility of such damages that one may encounter. Without limiting the foregoing, you understand and agree that
Premier Accessory Group, LLC has no liability for any damages or destruction to the consumer electronics devices or
other personal property that are contained in inside or outside the Premier Accessory Group, LLC products. This
includes without limitation, laptops, cellular phones, or other hand-held devices, or any loss of data contained on
the foreign device. Notwithstanding any damages that you might incur for general damages in contract, tort
(including negligence) or otherwise), the entire aggregate liability of Premier Accessory Group, LLC and any of its
distributors and/or suppliers shall be limited to the amount actually paid by you for the Premier Accessory Group,
LLC product giving rise to liability. Some states and/or jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitations or exclusions may not apply to you. The limitations of
liability set forth above shall apply to the maximum extent permitted under applicable law.
MODEL #: WI-TW455X
IC: 20526-WITW455X
FCC: 2AFM7WI-TW455X
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Any changes or modifications not expressly
approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and
receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been
evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without
restriction
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Any changes or modifications not expressly
approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the
equipment and
receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver
is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been
evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without
restriction
Wicked Audio® is a registered trademark of Premier Accessory Group, LLC
Premier Accessory Group, LLC
21 Commerce Drive
Cranbury, NJ 08512
Model numbers associated with this product:
WI-TW4550, WI-TW455X